Plumber's Essentials: Your Key to Installing a Bathtub
Plumber's Essentials: Your Key to Installing a Bathtub
Blog Article
We've stumbled on this article involving How to Install a Bathtub Yourself directly below on the web and thought it made good sense to relate it with you on this site.
Setting up a tub isn't specifically rocket science, however it does call for strong plumbing, woodworking, as well as sometimes, tiling abilities. Changing an old bathtub with a new one is additionally a moderately hard project. If the old bathtub is easily available, the job can relocate easily; if you need to open up a wall surface to remove the old tub as well as place the brand-new bath tub, the job is a lot harder. In either case, the task is within a home handyman's abilities, although you will require an assistant to leave the old tub and embeded in the new one. Make sure you have actually qualified yourself for the job as well as are comfortable attempting it. Rather than working with a service provider to take over a halfway-completed task, it is better to think about utilizing one prior to you begin. Opportunities are you might require an expert plumber to make tube connections.
This write-up will certainly aid you mount a new bathtub in your shower room if you have already bought a new tub and do not need to transform the arrangement of your previous water system pipelines.
Your devices as well as product list ought to comprise the following:
Preparing for the Setup
To start with, the supporting framework supplied with the bathroom must be fitted (if called for) according to the supplier's guidelines. Next, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is essential to ensure that if the faucet includes a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bath, it is additionally sensible to fit a supporting plate under the taps device to prevent stress on the bath tub.
Fit the adaptable faucet connectors to the bottom of the two faucets using 2 nuts as well as olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet through the hole in the bathroom. Use the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. Ensure you make use of every one of the provided washers.
Attach the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath must now prepare to be suited its final setting.
Removing Old Touches
If you require to change old taps with brand-new ones as a part of your installment, then the first thing you ought to do is disconnect the water system. After doing so, turn on the faucets to drain pipes any water continuing to be in the system. The process of getting rid of the existing faucets can be quite troublesome due to the restricted access that is commonly the instance.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the faucets. Have a fabric all set for the remaining water that will certainly come from the pipelines. As soon as the supply pipelines have been eliminated, make use of the same device to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from transforming throughout this procedure. When the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleaned of any kind of old securing compound.
Before proceeding to fit the new taps, compare the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the new taps, after that a shank adapter is required for the new taps to fit.
Installing the Bathtub
Utilizing both wooden boards under its feet, position the tub in the required setting. The wood boards are helpful in uniformly spreading out the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto four small points.
The following goal is to make sure that the tub is leveled all round. This can be achieved by checking the level and readjusting the feet on the tub until the spirit level reads degree.
To set up faucets, fit the bottom of the furthest adaptable tap adapter to the suitable supply pipeline by making a compression sign up with; after that do the very same for the other faucet.
Switch on the supply of water and also examine all joints as well as brand-new pipework for leakages and tighten them if essential. Load the bath tub as well as additionally examine the overflow outlet as well as the normal outlet for leakages.
Lastly, take care of the bath paneling as described in the maker's user's manual. Tiling and securing around the bathtub must wait till the bathtub has actually been made use of at least once as this will settle it into its final position.
Suitable New Taps
If the tails of the new taps are plastic, after that you will need a plastic port to avoid damage to the thread. One end of the adapter fits on the plastic tail of the faucet and also the other end supplies a connection to the existing supply pipes.
If you require to fit a monobloc, after that you will require minimizing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, position the faucet in the installing hole in the bath/basin guaranteeing that the washers are in location between the faucet as well as the sink. Secure the tap in place with the manufacturer supplied backnut. When the faucet is safely in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular faucet adapters. The previous type ought to be attached to the tap ends first, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the location where the bathroom meets the tile, it is necessary to seal the accompanies a silicone rubber caulking. This is essential as the fitting can move enough to crack a rigid seal, triggering the water to penetrate the wall in between the bathroom as well as the tiling, bring about issues with dampness and also possible leakages to the ceiling listed below.
You can pick from a selection of coloured sealants to blend in your fixtures and also installations. They are marketed in tubes and cartridges, as well as are capable of sealing spaces up to a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with spins of drenched paper or soft rope. Bear in mind to always load the tub with water before securing, to enable the motion experienced when the bathtub remains in use. The sealer can break relatively very early if you do not take into account this motion prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise conveniently readily available on the market. It is suggested to fit the floor tiles utilizing waterproof or waterproof sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you enjoyed our article about Tools You Need to Install a New Bathtub . Thanks a ton for taking the time to read our content. Appreciated our posting? Please share it. Help another person check it out. I cherish reading our article about How to Install a Bathtub.
Burst? Reach us! Report this page